Amplitude modulation is used in AM radio.
Answer is A.
Answer:
Amplitude modulation is used in AM radio.
Explanation:
Information signals must be transported between a transmitter and a receiver on some form of transmission medium. However, information signals rarely find a suitable way to transmit. Therefore, modulation is defined as the process of transforming information from its original form to a form more suitable for transmission, and is performed on the transmitter in a circuit called a modulator.
AM means modulated amplitude or amplitude modulation; it consists in varying the amplitude of a carrier wave of relatively high frequency according to the amplitude of the modulating signal (information). Frequencies that are high enough to radiate efficiently through an antenna and propagate through free space are commonly called radio frequencies.
AM was the first technique that was used to make radio.
Then amplitude modulation is used in AM radio.
Runner A had the highest velocity. Runner C had the lowest velocity. Runners A and B started at the same position, but runner C started ahead of runners A and B. What did you include in your response? Check all that apply.
Runner A had the highest velocity.
Runner C had the lowest velocity.
Runners A and B started at the same position.
Runner C started ahead of runners A and B.
Answer:
A. C. and D.
Explanation:
Answer:
A, C, and D
Just confirming
Denise is conducting a physics experiment to measure the acceleration of a falling object when it slows down and comes to a stop. She drops a wooden block with a mass of 0.5 kilograms on a sensor on the floor. The sensor measures the force of the impact as 4.9 newtons. What’s the acceleration of the wooden block when it hits the sensor? Use F = ma.
A.
2.45 m/s2
B.
4.4 m/s2
C.
5.4 m/s2
D.
9.8 m/s2
Answer:
D!
Explanation:
Using the formula F = ma, you plug in 4.9 for F (force), and 0.5 for m (mass), then solve for a (acceleration).
Answer:
9.8 m/s^2
Explanation:
F=ma
The force is 4.9 N
The mass is 0.5 kg
The acceleration is what we are trying to figure out.
(Now, plug into the equation)
4.9= 0.5a
Take 4.9/0.5 to find the value of a, which is 9.8m/s^2
2. How much work does gravity do in causing a 6 kg hammer to fall to the ground from a
height of 10 m?
Answer:
Therefore, gravity does 588.6 Joules of work in causing the 6 kg hammer to fall 10 meters.
Explanation:
Gravity does work by exerting a force on the hammer over a certain distance. We can calculate this work using the formula:
Work = Force x Distance (where force is parallel to the direction of movement)
In this scenario:
Force = Gravitational force acting on the hammer (Weight of the hammer)
Distance = Height fallen
Force:
We can calculate the gravitational force (weight) using the formula: Weight = Mass x Gravity
Mass of the hammer (m) = 6 kg
Gravity (acceleration due to gravity) = 9.81 m/s² (approximately)
Weight = 6 kg * 9.81 m/s² = 58.86 N (Newtons)
Distance:
Distance (d) = 10 m
Work done by gravity:
Work = Force x Distance = 58.86 N * 10 m = 588.6 Joules
Therefore, gravity does 588.6 Joules of work in causing the 6 kg hammer to fall 10 meters.
What are the coefficients of the equation below when is balanced?
A) 3, 2, 1,6
3CaCl2 + 2Na3PO4 --> 1Ca3(PO4)2 + 6NaCl
EXPLAIN the measures that can be taken to ensure safety in a storm.
Hello There!
Great Question You Asked.
I Will Provide A Number Of Steps To Below To Show You Measures of Being Safe
Number 1.
Find shelter immediately. If you find yourself caught in a lightning storm, the key to minimizing danger is to get inside a protective structure. While most people seek shelter if lightning appears to be near, people commonly wait too long to seek shelter. If you can detect lightning, it may be close enough to strike you so always make sure you are safe.
Number 2.
Try to stay away from windows because windows provide a direct path for lightning.
Number 3.
Don’t touch anything metal or electrical.
PLEASE HELP ASAP
What is the clockwise torque on the following lever?
5.0 Nm
125 Nm
250 Nm
0.0 Nm
Torque = (force perpendicular to the radius) x (length of the radius)
Torque = (25 N) x (5 m)
Torque = 125 N-m
Bro the answer you want is 125 NM
Hope this helps have a great day
A force of 5 N accelerates an object. The object’s mass is 50 g. What is the acceleration of the object? (Formula: F=ma)
0.01 m/s2
0.1 m/s2
10 m/s2
100 m/s2
Answer:
100 m/s²
Explanation:
First, convert to SI units:
50 g = 0.050 kg
Now plug into the formula:
F = ma
5 N = (0.050 kg) a
a = 100 m/s²
A force of 5 N accelerates an object. The object’s mass is 50 g. Then acceleration of the object is 100 m/s².
The formula linking force, mass, and acceleration is given by
F = ma,
Where F = the force applied to the object,
m = the mass of the object,
and a =the resulting acceleration.
In this case, the force is 5 N and the mass is 50 g, or 0.05 kg (remember to convert grams to kilograms).
Now, we can solve for the acceleration using:
a = F/m
a = 5 N / 0.05 kg
a = 100 m/s²
So the acceleration of the object is 100 m/s².
To learn about Kinetic Energy click:
brainly.com/question/26472013
#SPJ7
Cattle ranchers and dairy farmers rarely allow all of their animals to reproduce. Instead, they practice selective breeding and only encourage the reproduction of animals with specific features.
Which of the following cows would a dairy farmer most likely choose to reproduce?
A.
a cow that makes a lot of milk
B.
a cow that can run quickly
C.
a cow with thick, soft fur
D.
a cow with large, strong hooves
Answer:
A
Explanation:
I believe the answer would be A because they are gonna want a cow who can produce a lot of milk because then they can sell what milk is left over to the people
They practice selective breeding and only encourage the reproduction of animals with specific features such as cow that makes a lot of milk.
What is the main aim of dairy farmers for breeding?The Cattle ranchers and dairy farmers do selective breeding so that they produce an offspring that have high milk production capabilities. Dairy farmers rear animals for milk production.
So we can conclude that they encourage the reproduction of animals with specific features such as cow that makes a lot of milk.
Learn more about reproduction here: https://brainly.com/question/815744
How much heat is absorbed by a 67g iron skillet when its temperature rises from 14oC to 22oC?
Explanation:
The heat (thermal energy) absorbed by the iron skillet can be found using the following equation:
[tex]Q=m.C.\Delta T[/tex] (1)
Where:
[tex]Q[/tex] is the heat
[tex]m=67 g[/tex] is the mass of the element (iron in this case)
[tex]C[/tex] is the specific heat capacity of the material. In the case of iron is [tex]C=0.444\frac{J}{g\°C}[/tex]
[tex]\Delta T=T_{f}-T_{i}=22\°C - 14\°C= 8\°C[/tex] is the variation in temperature
Knowing this, lets rewrite (1) with these values:
[tex]Q=(67 g)(0.444\frac{J}{g\°C})(8\°C)[/tex] (2)
Finally:
[tex]Q=237.98 J[/tex]
How are volcanoes and wind similar? A. They both create igneous rock. B. They both can be constructive forces. C. They both form deltas. D. They are both a form of physical weathering.
B. They both can be constructive forces.
Both volcanos and wind can shape the landscape... volcanos using eruptions and lava, wind using wind erosion when it gets "windy".
Hope this helps.
r3t40
20. Consider two Stars A and B with temperatures Ta and TB and radii Ra and RB respectively. If TA
= 2 TB and Ra= 12 RB, which statement about the stars' luminosities, LA and LB, is true?
using this formula: L=(R^2)(T^4)
a) La =LB
b) La = 2 LB
La=4 LB
d) La = 12 LB
e) La = 14 LB
Answer:
[tex]L_A = 9 L_B[/tex]
Explanation:
The formula that relates the luminosity of a star (L) to its radius (R) and the temperature (T) is
[tex]L=\frac{R^2}{T^4}[/tex]
For star B, we can write:
[tex]L_B=\frac{R_B^2}{T_B^4}[/tex]
For star A, we have
[tex]T_A = 2 T_B\\R_A = 12 R_B[/tex]
So the luminosity of star A is
[tex]L_A=\frac{R_A^2}{T_A^4}=\frac{(12 R_B)^2}{(2 T_B)^4}=\frac{144 R_B^2}{16 T_B^4}=9\frac{R_B^2}{T_B^4}=9 L_B[/tex]
16. A 6 kg block is falling toward a spring located 1.8 m below. If it has a speed of 4 m/s at first,
what will be the maximum compression of the spring? Assume the spring constant is 2000 N/m
[6 marks][1 mark for Comm]
Answer:
Maximum compression of the spring: [tex]\rm 0.423\; m[/tex].
Explanation:
Let [tex]x[/tex] be the maximum compression, in meters, of the spring.
What's the initial kinetic energy of this block?
The initial velocity [tex]v[/tex] of the block is [tex]\rm 4\;m\cdot s^{-1}[/tex].The mass of the block is [tex]\rm 6\;kg[/tex].Initial [tex]\displaystyle \mathrm{KE} = \frac{1}{2} \;m\cdot v^{2} = \rm \frac{1}{2} \times 6\times 4^{2} = 48\;J[/tex].What's the final kinetic energy of this block?
The block would have come to a stop by the time the spring reaches its maximum compression. [tex]v = 0[/tex]. As a result, the final kinetic energy of the block shall also be zero.Let the initial height of the block be zero.
The height of the block will be [tex]\rm -1.8\;m[/tex] by the time it reaches the top of the spring. However, the height of the block will become even more negative as the spring compresses. If the maximum compression of the spring is [tex]x[/tex] meters, the height of the block will be [tex]-(1.8 + x)[/tex] meters by the time the spring reaches its maximum compression.
The change in the height of the block will thus be [tex]-(1.8 + x)\;\mathrm{m}[/tex] relative to the initial position of the block. The change in the block's potential energy due to gravity will be:
[tex]\Delta \mathrm{GPE} = m\cdot g\cdot \Delta h = 6\times 9.8 \times (-(1.8 + x)) = -105.948- 58.86\;x[/tex].
The mechanical energy of an object is the sum of its kinetic energy and its potential energy. What will be the change in the mechanical energy of the block?
[tex]\text{Change in Mechanical Energy} \\ = \text{Change in KE} + \text{Change in PE} \\ = (0 - 48) + ((-105.948- 58.86\;x) - 0)\\ = (-153.948 - 58.86\;x)\; \text{J}[/tex].
The block has lost [tex](153.948 + 58.86\;x)\; \text{J}[/tex] of energy as it travels from its initial position to the place where the spring is most compressed. Energy conserves. Those energies are transferred to the spring. Assume that there's no energy loss in this process. All those [tex](153.948+ 58.86\;x)\; \text{J}[/tex] would have become the elastic potential energy of the spring.
On the other hand, it is assumed that the spring is compressed by a distance of [tex]x[/tex] meters. By Hooke's Law, the elastic potential energy of the spring will be:
[tex]\displaystyle \text{Elastic Potential Energy} = \frac{1}{2} \; k\cdot x^{2} = \frac{1}{2}\times 2000 \times x^{2} = 1000\; x^{2}\;\text{J}[/tex].
There are thus two expressions for the Elastic Potential Energy of the spring:
[tex](153.948+ 58.86\;x)\; \text{J}[/tex] from the conservation of energy, and[tex]1000\; x^{2}\;\text{J}[/tex] by Hooke's Law.The two expression shall be equivalent. Equate the two expressions and solve for the compression of the spring, [tex]x[/tex].
[tex]153.948+ 58.86\;x = 1000\; x^{2}[/tex].
[tex]1000\; x^{2}- 58.86\;x - 153.948 = 0[/tex].
[tex]\displaystyle x_{1} = \frac{-(-58.86) +\sqrt{(-58.86)^{2} - 4\times 1000 \times (-153.948)}}{2\times 1000} = \rm 0.423[/tex].
[tex]\displaystyle x_{2} = \frac{-(-58.86) +\sqrt{(-58.86)^{2} - 4\times 1000 \times (-153.948)}}{2\times 1000} = -0.364[/tex].
Consider the expression for the height of the block when it is at the top of the spring and when the spring reaches maximum compression:
Height of the block at the top of the spring: [tex]\rm -1.8\;m[/tex];Height of the block when the spring reaches maximum compression: [tex]-(1.8 + x) \; \text{m}[/tex]. This height will be [tex]\rm -2.2\; m[/tex] if [tex]x_{1}[/tex] is correct, and [tex]\rm -1.4\; m[/tex] if [tex]x_{2}[/tex] is correct. The block compresses the spring and will be below its initial position at the top of the spring. Therefore, [tex]x > 0[/tex] and only [tex]x_{1}[/tex] is correct.The maximum compression of the spring will be 0.423 meters.
what may happen if oceanic plates stop moving
Answer:
the earth would be a different place, for example there wouldnt be anymore volcanic eruptions
Explanation:
when the earth plates stops moving is the source to everything, the ground would shake, waves would stop ect
There would be no new island formations when oceanic plates stop moving.
Explanation:
The oceanic plate or the tectonic plate movement determines the several activity of land and ocean which keep making the life possible. As the plate movement stop, volcanic eruption will be stopped, sea floor will not spread further, every activity below ground will cease.
The pressure increases inside the core and so does the erosion. The continent will be lost with all its life on the land. Oceanic life will survive more but may freeze the planet to die.
Molecules can be made of atoms Of
the same element only
different elements only
the same or different elements
Answer:
Molecules can be made of the atoms of same element as well as of the different elements.
Explanation:
H2 is called a molecule because it is made up of atoms of same elements H.
Also, H2O is called a molecule as it is made up of atoms of different elements H and O.
Answer:
The same or different elements
Explanation:
I did this question, thats correct.
Two balls are placed near one another and hang down, as
shown below.
Which conclusion is supported by this evidence?
Neither ball has a charge.
The balls are both positively charged.
One ball is positively charged, and the other is negatively
charged
Each ball has a charge, but the type of charge is
unknown
Mark this datum
Save and Exit
Submit
Answer:
Neither ball has a charge.
Explanation:
Conclusion 1 is supported by this evidence. Neither ball has a charge. because the charge is in hanging condition neither attract nor repel each other.
What is the charge?When the matter is put in an electromagnetic field, it has an electric charge, which causes it to experience a force. A positive or negative electric charge can exist.
Charges that are similar repel each other, whereas charges that are dissimilar attract each other. The term "neutral" refers to an item that has no net charge.
The charge is in hanging condition neither attract nor repel each other. Shows neither ball has a charge.
Hence conclusion 1 is supported by this evidence.
To learn more about the charge refer to the link;
https://brainly.com/question/24391667
Photoelectrons with a maximum speed of 7.00 · 105 m/s are ejected from a surface in the presence of light with a frequency of 8.00 · 1014Hz. If the mass of an electron is 9.1 · 10-31 kg, calculate the maximum kinetic energy of a single electron, in joules.
_____ J
6.3 x 10-25
4.4 x 10-19
3.2 x 10-25
2.2 x 10-19
Answer:
2.2 x 10-19
Explanation:
Kinetic Energy = 1/2 m v ^2
Find the acceleration of the block.
Answer:
C. 7 m/s²
Explanation:
The horizontal forces acting on the block are the 80 N tension, the 60 N tension, and friction. Apply Newton's second law:
∑F = ma
80 N − 60 N − F = (10 kg) (1 m/s²)
20 N − F = 10 N
F = 10 N
If S₁ goes away, the acceleration becomes:
∑F = ma
80 N − 10 N = (10 kg) a
70 N = (10 kg) a
a = 7 m/s²
Which natural process is responsible for ridge push
Answer:
seafloor spreading
Explanation:
PhYsIcS
suppose a scientist found a new matal-like substance in the desert. He determined its mass to be 20 grams. The volume was determined by water displacement to be 5 cm^3. What is the density of the substance? Will it sink or float in liquid water ( 1g/cm^3)?
Density = (mass) / (volume)
Density = (20 g) / (5 cm³)
Density = 4 g/cm³ .
The density of the substance is greater than the density of water. A lump of the substance will sink in water, unless the lump is formed into a shape that displaces 20 cm³ of water or more, such as a tiny boat shape.
IDENTIFY the common types of precipitation. COMPARE and CONTRAST them.
The most common types of precipitation are:
- rain
- snow
- hale
The rain comes in liquid form. In order for the rain to occur, the temperature in the upper parts of the troposphere should not be too low, thus the condensation of the water vapor can only go from gaseous to liquid form. The rain occurs in the lower latitudes, as well as in the mid-latitudes mostly from spring to autumn.
The snow occurs in the higher latitudes and in the mid-latitudes during winter. In order for the snow to form, the temperatures in the upper parts of the troposphere should be below the freezing point, so the water vapor crystallizes into small ice crystals.
The hale occurs in the warmer period in the mid-latitudes, and occasionally in the lower latitudes. The hale is formed when during the condensation of the water vapor into liquid form, the air mass encounters much lower temperatures below the freezing point. This results in the formation of large crystals that fall on the surface in the form of frozen, circular-shaped pieces.
7. How much thermal energy is absorbed when 10.0 g of ice at 0.0 degrees C changes phase to liquid water at 0.0 degrees C? The molar mass, M, of water is 18.02 g/mol and the theoretical heat of fusion, Hfus, of water is 6.01 kJ/mol
Answer:
3.34 kJ
Explanation:
FIrst of all, we need to calculate the number of moles corresponding to 10.0g of ice. This is given by
[tex]n=\frac{m }{M_m}[/tex]
where
[tex]M_m = 18.02 g/mol[/tex] is the molar mas
m = 10.0 g is the mass
Substituting
[tex]n=\frac{m}{M_m}=\frac{10 g}{18.02 g/mol}=0.555 mol[/tex]
Now we know that the heat of fusion is
[tex]H_{fus}=6.01 kJ/mol[/tex]
so the thermal energy needed to fuse the ice is
[tex]Q=n H_{fus} = (0.555 mol)(6.01 kJ/mol)=3.34 kJ[/tex]
Hurricanes can be very destructive, bringing tornadoes, flooding, strong winds, and storm surges to the land areas they come in contact with. What is a storm surge? a wall of water that is pushed ashore a large, rotating, low-pressure storm a strong, narrow current that flows rapidly away from the beach a large ocean wave usually caused by an undersea earthquake
Answer:
DescriptionA storm surge, storm flood, tidal surge or storm tide is a coastal flood or tsunami-like phenomenon of rising water commonly associated with low pressure weather systems, the severity of which is affected by the shallowness and orientation of the water body relative to storm path, as well as the timing of tides.
A wall of water that is pushed ashore is a storm surge. So, the correct option is A.
What is Storm surge?A coastal flood or tsunami-like event of rising water known as a storm surge, storm flood, tidal surge, or storm tide is frequently linked to low-pressure weather systems like cyclones. It excludes waves and is calculated as the rise in the water level just above typical tidal level.
Extreme coastal as well as interior flooding may be the result of the seawater's pulse when it reaches the coast. Storm surge can sometimes be much more destructive than the thunderstorms that produce it.
An anomalous increase in water caused by a storm that is higher than the expected astronomical tides is known as a storm surge. Storm tide, which is referred to as the increase in water level brought on by a storm surge and an astronomical tide, shouldn't be confused with storm surge.
Therefore, the correct option is A.
Learn more about Storm surge, here:
https://brainly.com/question/29491314
#SPJ3
Your question is incomplete, mot probably the complete question is:
Hurricanes can be very destructive, bringing tornadoes, flooding, strong winds, and storm surges to the land areas they come in contact with. What is a storm surge?
a wall of water that is pushed ashorea large, rotating, low-pressure storma strong, narrow current that flows rapidly away from the beacha large ocean wave usually caused by an undersea earthquakeUrgent!!!!!! 20 points!!!!!!
how are the speed, wavelength and frequency of a wave related
Answer:
The higher the frequency, the shorter the wavelength. Because all light waves move through a vacuum at the same speed, the number of wave crests passing by a given point in one second depends on the wavelength. Speed shows how long it takes for wavelengths to travel.
Raymond requires extensive knowledge of SQL and Bugzilla. What is Raymond’s job role?
A.
mobile app tester
B.
mobile app developer
C.
iOS architect
D.
senior iOS developer
B} Mobile app developer （╹◡╹）
None of the options provided specifically require the skills of SQL and Bugzilla, but based on these skills, Raymond is likely to work in a broader role related to database management, software development, or quality assurance such as a Database Administrator or a Quality Assurance Engineer.
Explanation:Based on the requirement of having extensive knowledge of SQL and Bugzilla, it's likely that Raymond could be working in a role related to database management or testing. However, none of the listed options, which include Mobile App Tester, Mobile App Developer, iOS Architect, and Senior iOS Developer, specifically require these skills.
Most likely, Raymond is working in a broader role in software development or quality assurance. SQL (Structured Query Language) is a programming language used for managing and manipulating databases, while Bugzilla is a web-based general-purpose bug tracking system and testing tool. Therefore, his role could be a Database Administrator or a Quality Assurance Engineer.
Learn more about Job Role here:https://brainly.com/question/12541329
#SPJ12
Where can we witness conduction, convection, and radiation in the Earth's spheres?
convection of heat in the asthenosphere, conduction of heat from the inner core, and radiation of the inner core throughout the other layers
If some electrons are transferred from object A to object B,
A. Object A will have a positive charge
B. Object A will have a negative charge
C. Object B will have a positive charge
D. B and C
Answer: A. Object A will have a positive charge.
Explanation: If the number of protons and electrons are the same, their net charges cancel each other out, and you have a neutral charge. If electrons are transferred to another object, the amount of positive charge will outweigh the amount of negative charge. As a result, you are left with an overall positive charge in object A. Meanwhile, object B is now negative.
Final answer:
When electrons are transferred from object A to object B, object A will become positively charged (option A) due to the loss of negatively charged electrons. This makes the answer A. Object A will have a positive charge.
Explanation:
If some electrons are transferred from object A to object B, the correct answer is A. Object A will have a positive charge. This is because electrons have a negative charge, and removing them from an object leaves that object with an excess of positive charge in the form of protons (which are positively charged and present in every atom). Object B, receiving the electrons, will become negatively charged since it gains additional negative charges.
With reference to the information provided:
Ball 1 (analogous to object A) will have a positive charge if it loses electrons.Ball 2 (analogous to object B) will have a negative charge if it gains electrons.If a positively charged object is in contact with an uncharged object in a closed system, the uncharged object will become positively charged.Give 3 examples of something with kinetic energy.
Explanation:
Radio wavesstatic electricity a car moving along the road3 examples of kinetic energy:
The river flow down the stream or the falling at the gorge has kinetic energy possessed in it. The basketball dribbled down which bounces back to the certain height has the kinetic energy in the ball. The shooting star falls down in the sky or space with the kinetic energy in it.Kinetic energy is the form of energy which is associated with motion of the body who possesses it. Kinetic energy is dependent upon “mass and velocity” of the body.
what is the net force if one person is pushing on a box with 60 N of force to the right and another person is pushing on the box with 30 N of force to the left?
Answer:
The net force on the box is 30 N to the right.
Explanation:
To find the net force on the box, we must add all of the forces together. In order to do this successfully, we must establish a positive and a negative direction. Let’s say that the positive direction is towards the right and the negative direction is towards the left.
Knowing this, we can set up the following equation:
Net force = F1 + F2
Now we can substitute in our known values for the forces given in the problem.
Net force = 60 N + (-30 N)
If we simplify and solve, we get
Net force = 60-30 = 30 N
Since we established the right as the positive direction, we know that the answer is 30 N to the right. If we think about this problem conceptually, this answer makes sense because the 30 N force to the left cancels out 30 N of the force towards the right, because they are acting in opposite directions.
Hope this helps!
A 6.0-ohm resistor that obeys Ohm’s Law is connected to a source of variable potential difference. When the applied voltage is decreased from 12 V to 6 V, the current passing through the resistor
a.
remains the same
b.
is doubled
c.
is halved
d.
is quadrupled
Is halved. A 6Ω resistor connected to a voltage source which voltage is decreased from 12V to 6V the current passing through the resistor is halved.
The key to solve this problem is applying Ohm's Law V = R I, clearing I from the equation, we obtain I = V/R. Then, the current is directly proportional to the voltage and inversely proportional to the resistance.
V = 12V and R = 6Ω
I = 12V/6Ω = 2A
V = 6V and R = 6Ω
V = 6V/6Ω = 1A
As we can see the current is halved if the voltage descreased from 12V to 6V
The correct option is
(c) is halved.
Given a 6Ω resistor and the voltage is decreased from 12V to 6V
Ohm's Law:
Ohm's law states that the current (I) is directly proportional to the voltage (V) and inversely proportional to the resistance (R). That is
V= I/R
here, according to the question
initially, V = 12V and R = 6Ω
so I = 12V/6Ω = 2A
Finally
V = 6V and R = 6Ω
I' = 6V/6Ω = 1A
so we see that
2I' = I
I' = I/2
Hence, the current is halved.
Learn more about Ohm's Law:
https://brainly.com/question/796939?referrer=searchResults
what is a goal of the planned missions MIRI?
the answer is to explore the kupier belt
Answer:
Its goal is to explore the Kupier Belt, a region in space where comets originate
Explanation:
The Mid-Infrared Instrument (MIRI) is a telescope with abilities to see the mid-infrared region of the electromagnetic spectrum.The wavelength of this instrument is 5-28 microns. The Kupier belt is a region in space beyond Neptune.MIRI was developed to enable scientists study and explore the kupier belt to observe the far most galaxies, new stars that are formed and the comets invisible from the previous telescopes.
Exploring the Kuiper Belt is a common objective for certain space missions. Previous missions like the NASA Pioneers 10 and 11 helped pave the way for future explorations, which now include plans to explore moons like Europa for signs of life.
Explanation:The planned missions that this question refers to are likely spacecraft designed to explore the outer regions of our solar system, including destinations such as the Kuiper Belt. The primary goal of such missions is often to gather data about the composition, structure, and the variety of objects within the Kuiper Belt. Notable examples of past missions with similar objectives include NASA's Pioneers 10 and 11 which were pioneers in interplanetary space travel, aiming to assess the feasibility of navigating through the asteroid belt beyond Mars and to measure radiation hazards in Jupiter's magnetosphere. They provided essential data that informed the design of future space missions. An upcoming significant mission is the Europa Clipper, which aims to explore Europa, one of Jupiter's moons, to understand its subsurface ocean and the potential for life there.