• Most of the galaxies in the universe are moving away from
Earth. Suppose a particular galaxy emits orange light with
a frequency of 5.00 * 1014 Hz. If the galaxy is receding
from Earth with a speed of 3325 km/s, what is the
frequency of the light when it reaches Earth?
• A) 4.945 x 1014 Hz
• B) 5.542 1012 Hz
• C) 5.055 1014 Hz​

Answer:

I = 24 A

Explanation:

This is Parallel Circuit and it is the first principle of parallel circuit that voltage will be equal in all components in the circuit

It includes 10 resistors Therefore the voltage across,

R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 = R9 = R10 = voltage in battery

We will apply Ohm's Law to each resistor to find its current because we know the voltage across each resistor is 12 V  and the resistance of each resistor is 5Ω

I (R1) = E (R1) / R1

I (R1) = 12v / 5Ω

I (R1) = 2.4 A

The value resistance E of all resistors are same therefore by applying the formula above the value of current in all resistors will be 2.4 A

The Total current in the circuit will be

I (total) = I (1) + I (2) + I (3) + I (4) + I (5) + I (6) + I (7) + I (8) + I (9) + I (10)

I (total) = 2.4 + 2.4 + 2.4 + 2.4 + 2.4 + 2.4 + 2.4 + 2.4 + 2.4 + 2.4

I (total) = 24 A

Answer:

500 nm

Explanation:

[tex]\lambda = c/\nu = \frac{3*10^8}{6*10^{18}} = 5*10^{-11}[/tex] m

Answer:

5*10^-11

Explanation:

From alvs

-- A horizontal line on a position/time graph says that as time goes on, the position isn't changing.  The object is standing still. At rest. Motionless.

-- A horizontal line on a speed/time graph says that as time goes on, the speed isn't changing.  If that doesn't happen to be zero, then the object is moving at a constant speed, and its position keeps changing at constant rate.  On a position/time graph, this same motion would be a straight line slanting  upward.

Final answer:

A horizontal line on a position vs. time graph indicates an object at rest, while a horizontal line on a speed vs. time graph shows an object moving at a constant speed.

Explanation:

Graphs play an essential role in analyzing motion in physics. The representation of motion on position vs. time graphs and speed vs. time graphs can tell us a lot about the behavior of moving objects.

When examining a position vs. time graph, a horizontal line indicates that the position of an object does not change as time passes, which means the object is stationary or at rest. There is no change in position, so the velocity is zero. On the other hand, a horizontal line on a speed vs. time graph suggests that the object is moving at a constant speed. The flat line indicates that the speed does not change over time; the object is not accelerating or decelerating.

To sum up, a horizontal line on a position graph signifies no movement (zero velocity), while a horizontal line on a speed graph indicates constant movement (constant speed).

Final answer:

A horizontal line on a position vs. time graph indicates an object at rest, while a horizontal line on a speed vs. time graph shows an object moving at a constant speed.

Explanation:

Graphs play an essential role in analyzing motion in physics. The representation of motion on position vs. time graphs and speed vs. time graphs can tell us a lot about the behavior of moving objects.

When examining a position vs. time graph, a horizontal line indicates that the position of an object does not change as time passes, which means the object is stationary or at rest. There is no change in position, so the velocity is zero. On the other hand, a horizontal line on a speed vs. time graph suggests that the object is moving at a constant speed. The flat line indicates that the speed does not change over time; the object is not accelerating or decelerating.

To sum up, a horizontal line on a position graph signifies no movement (zero velocity), while a horizontal line on a speed graph indicates constant movement (constant speed).

Answer:

-$1,000

Explanation:

$3000 - $4000

Answer:

-1000

3000-4000=-1000

Answer:  

The first graph is the trend line.

Explanation:

Trend Line

It's a line indicating the tendency of something being measured or evaluated. The trend line is meant to represent an approximation of a set of points of a measured magnitude.  

We have three possible 'trend lines' to choose from. The second is not a line, so it's not the correct option. The third is not a line either, it's just a graph who joins all the measured points. It doesn't mark a trend.

The first graph is a trend line because it's a single line and can be used to represent the whole set of values  .

A muddy floor can be very slippery so if you jump on a muddy floor, you will most likely slip and hurt yourself.

A hard floor will most likely be dry. So when you jump on a hardwood floor, you are less likely to slip. But, you can hurt your knees if you're not careful.

Answer:

Injury can occur

Explanation:

you might be running then you start jumping without putting your heels down, then might get achilles tendonitis in your achilles tendons.

Answer:

B) [tex]R= \sqrt{(40N)^2+(30N)^2}[/tex]

Explanation:

Given [tex]\sum Fx=40N\ \ \ \ \ \ \ \ \ \sum Fy=30N[/tex]

As the forces are on X and Y-axis. We can see the angle between the forces is 90°

Using vector addition formula. Since the angle between the forces is 90°

[tex]R=\sqrt{\sum (Fx)^2+\sum (Fy)^2}[/tex]

[tex]R= \sqrt{(40N)^2+(30N)^2}[/tex]

Please see the attachment.

1) The new gravitational force is half of the original force

2) The new gravitational force is 1/8 of the original force

Explanation:

1)

Let's call F the initial gravitational force between the object A and B. The magnitude of F is given by the equation

The magnitude of the gravitational force between two objects is given by

[tex]F=G\frac{m_A m_B}{R^2}[/tex]

where

[tex]G=6.67\cdot 10^{-11} m^3 kg^{-1}s^{-2}[/tex] is the gravitational constant

[tex]m_A,m_B[/tex] are the masses of the two objects

R is the separation between them

In this part of the problem, we are told that the distance between the two objects doubles, so the new distance is

R' = 2R

While the mass of object A is doubled, so the new mass is

[tex]m_A' = 2m_A[/tex]

Therefore, the new gravitational force is

[tex]F' = \frac{Gm_A' m_B}{R'^2}= \frac{G(2m_A) m_B}{(2R)^2}=\frac{1}{2}(\frac{Gm_A m_B}{R^2})=\frac{F}{2}[/tex]

Therefore, the new force is half of the original force.

2)

In this second part of the problem, the distance between the two objects doubles, so the new distance is

R' = 2R

While the mass of object A is halved, so the new mass is

[tex]m_A' = \frac{m_A}{2}[/tex]

Therefore, the new gravitational force this time is:

[tex]F' = \frac{Gm_A' m_B}{R'^2}= \frac{G(m_A/2) m_B}{(2R)^2}=\frac{1}{8}(\frac{Gm_A m_B}{R^2})=\frac{F}{8}[/tex]

Therefore, the new force is 1/8 of the original force.

Learn more about gravitational force:

brainly.com/question/1724648

brainly.com/question/12785992

#LearnwithBrainly

Answer:

Option D

2 m/s East

Explanation:

From the law of conservation of momentum, the sum of initial momentum equals the sum of final momentum

Momentum, p=mv where m is the mass and v is the velocity

Since the masses are the same then

[tex]m(u_1+u_2)=m(v_1+v_2)[/tex]  

Therefore

[tex]u_1+u_2=v_1+v_2[/tex]

where [tex]v_1[/tex] and [tex]v_2[/tex] are final velocities of objects while [tex]u_1[/tex] and [tex]u_2[/tex] are the initial velocities respectively

Taking East direction as positive then West as negative and by substitution

[tex]2.5+-2.25=v_1-1.75[/tex]

Therefore

[tex]v_1=2 m/s[/tex] hence East since it's positive

Answer:

2 m/s east

just did it ;D

Explanation:

Answer:

The arc and flash burns results from high temperatures caused by an electric arc or explosion near the body

Explanation:

The arc and flash burn occurs due to high temperature because of electric arc or explosion near the body.  The basic reason for catching of fire is due to clothing. Because the fact the fabric catches fire more easily. For less damage the first thing one must follow is application of the antibiotic ointment as well as dressing soon. In severe cases it requires surgery. when electricity passes through our body causes burning very rapidly.

Final answer:

An electrical burn occurs when the skin is exposed to high temperatures from an electric arc or explosion, which can lead to serious complications, including dehydration, electrolyte imbalance, and infection. Immediate medical attention and treatment with IV fluids and nutrients are critical.

Explanation:

The type of burn described results from high temperatures caused by an electric arc or explosion near the body, which is often referred to as an electrical burn. These burns occur when the skin is damaged by intense heat from an electric source and can be extremely dangerous. They can be fatal due to the death of skin cells, leading to massive fluid loss, dehydration, electrolyte imbalance, and potential renal and circulatory failure.

Such burns require immediate medical treatment, which includes administering intravenous fluids to combat dehydration and providing intravenous nutrients to help the body repair tissues and replace lost proteins. Moreover, electrical burns increase the risk of infection as the damaged skin is more vulnerable to bacteria and pathogens.

Answer:

The force acting on the free-falling object is, F = 1.47 N

Explanation:

Given data,

The mass of the object, m = 150 g

When an object is under free-fall, the only force acting on the object is the gravitation force neglecting the air resistance.

So, when an object is close to the surface of the earth acceleration due to gravity acting on the object is equal to g.

The value of g at the surface of the Earth is, g = 9.8 m/s²

Therefore, the force acting on the object under free fall is,

                                                          F = mg

                                                              = 0.15 x 9.8

                                                               = 1.47 N

Hence, the force acting on the free-falling object is, F = 1.47 N

Answer: what comes to mind when we hear the word "Friction" ?

Basically friction is a "Force" that opposes an intend(ing) motion.

Explanation:

By motion I mean movement.

By force I mean a body that carries with it energy.

So to understand this better, just see it as a force(thing) that prevents or stops you from taking action.

Answer:

C. reflects one or more visible light frequencies.

Explanation:

The color that we see is the color that is deflected from the RGBHSB.etc. This means that the light has all the colors within, and the object it hits absorbs all but one color, in which it deflects for our eyes to see.

~

The exhaust temperature is 200 K

Explanation:

The maximum efficiency of a machine is given by the equation:

[tex]\eta=1-\frac{T_C}{T_H}[/tex]

where:

[tex]T_H[/tex] is the temperature of the hot reservoir

[tex]T_C[/tex] is the temperature of the cold reservoir

For the engine in this problem, we have:

[tex]\eta = 0.333[/tex] (efficiency is 33.3%)

[tex]T_H=300K[/tex] is the temperature of the hot reservoir

Re-arranging the equation for [tex]T_C[/tex], we can find the exhaust temperature (the temperature of the cold reservoir):

[tex]T_C=T_H(1-\eta)=(300)(1-0.333)=200 K[/tex]

Learn more about temperature:

brainly.com/question/1603430

brainly.com/question/4370740

#LearnwithBrainly

Answer:

200k

Explanation:

Answer:

Chimps and apes are still here because humans did not evolve from all apes and chimps.

Explanation:

Answer:

the Answer is A

Explanation:

because the swinging motion of a pendulum is due to the force of gravity generated by the earth's size

The other material would be needed for a student to construct a basic electric motor is a magnet.

Answer: Option A

Explanation:

For constructing fundamental electric motors coils of wire, the battery, few paper clips, a thermometer, and a magnet are mandatory. The principle on which it works is when in magnetic field rectangular coil placed and current passes than force will act on it and rotate it continuously to convert electrical energy into mechanical energy.

Here magnet is compulsory to generate motion when two bar magnets placed against the north and south pole of each other than attractive force but if placed in a similar direction than repulsive force occur. Therefore, these attractive and opposing forces generate rotational motion.

Answer:

The answer is A

Explanation:This is the answer

Answer:

A)

B)

Values of the domain that make sense would be those from 0 on because there are no negative number of sessions; values of range that make sense would be also those from 0 on because there are no negative number of pictures.

C)

[tex]f(x)=15x[/tex], where "x" is the number of sessions.

If we have 22 session then:

[tex]f(22)=15*22[/tex]; f(22)=[tex]f(22)=330[/tex]

Explanation:

Answer:

Option A

D = m/v

Explanation:

Density is defined as mass per unit volume of an object. Therefore, D=m/v where m is the mass of the object and v is the volume

Therefore, option A is the right option

The law of floatation states that, a floating body displaces its own weight of the fluid in which it floats.

Answer:

Alternating current

Explanation:

The electrical current periodically changes direction.

Answer:

alternating current

Explanation:

A stands for alternating

C stands for current

the current which changes direction ( several times per second ) is known as AC or alternating current

Answer:

an average of 92,955,807 miles

Explanation:

Answer:

First I should say that the Earth's orbit around the Sun is elliptical, not perfectly circular, so the Earth-Sun distance is changing as we speak just from the Earth traveling in its orbit around the Sun. There are some long-period oscillations, but those are very small, and don't imply that we're systematically moving towards or away from the Sun.

I hope this answer helps you :)

If the Moon were twice as big, its pattern of apparent shapes would be probably be reversed.

Option B

The motion or the movement of the earth and that of the moon trajectory are the same of one another. There are many reasons for the great differences in the earth and the space. But the gravity plays a very major and an important role in controlling all the activities of these celestial bodies.

The projectile motion plays a very important and a crucial role. It is plays were the parabolic motions and the paths come into act. They also move in a definite speed in order to control the movement.

Answer:

THE LAW OR PRINCIPLE OF SUPERPOSITION; States that when two identical waves are brought, the resultant disturbance is the algebraic sum of the individual disturbances of the two waves.

Explanation:

Most stationary waves are obtained as a result of the combination or superposition of an incident wave and it's reflected wave. Like in music, they result from the stationary waves of plucked strings leading to the Superposition law.

Peace.

Answer:  It is the way you can date layers of rocks, sediment and fossils.  The most recent layer is the youngest in geologic time, while the bottom layer is always the oldest.

Explanation:

a basic law of geochronology, stating that when there is any undisturbed sequence of rocks deposited in layers, the youngest layer is on top and the oldest on bottom, each layer being younger than the one beneath it and older than the one above it.

the question is correct

Explanation:

For projectile motion, use constant acceleration equation:

Δx = v₀ t + ½ at²

where Δx is the displacement,

v₀ is the initial velocity,

a is the acceleration,

and t is time.

Both objects are projected upward with velocity u.  The second object is thrown after a time t₀.

For the first object:

Δx = u t + ½ (-g) t²

Δx = u t − ½g t²

For the second object:

Δx = u (t−t₀) + ½ (-g) (t−t₀)²

Δx = u (t−t₀) − ½g (t−t₀)²

Assuming the objects meet, the displacements will be equal:

u t − ½g t² = u (t−t₀) − ½g (t−t₀)²

u t − ½g t² = u (t−t₀) − ½g (t² − 2tt₀ + t₀²)

u t − ½g t² = u t − u t₀ − ½g t² + g tt₀ − ½g t₀²

0 = -u t₀ + g tt₀ − ½g t₀²

0 = -u + g t − ½g t₀

g t = u + ½g t₀

t = u/g + t₀/2

Ocean Currents is the factor that determines the air temperature in coastal regions having same latitude.

Explanation:

There are factors that use to determine air temperature. They are latitude, altitude, region, water current, etc and it is based on the combination of water, air, and land.

If two coastal regions situated in the same latitude means they are not in the same region. Another city can be in the same latitude but in longitude. All the coastal regions don't have the same air temperature.

The air temperature in coastal regions can measured by the Ocean Current. A hypothesis of using cold water and warm water use to determine the air temperature.

Answer:

133 j

Explanation:

Answer:

That would be Spring C

Explanation:

i took the test :P

Answer:

The answer is C please give me brainliest

Explanation: